Skip to main content

Overhaul of WEBER #2 (The original blog was written on 26th Aug. 2007)

Yesterday, the removal of the WEBER was interrupted by the sticking nuts.


Today morning, I went to the DIY hardware store near my house thinking how I could remove the WEBER.
When I arrived at the store, “junk tool sale” was held at the store timely.  I got the combination wrench set with the special price 498JPY (about $4.5).  It seemed thinner and better than what I had used.  And I also got the disc grinder to make the special tool from my old tools because I thought I would struggle to loosen the nuts.

However, contrary to my expectation, I could loosen the nuts easily by new 498JPY combination wrench.  Great!  There was no turn for the disc grinder I bought…okay I wanted it before.  So, I could remove the WEBER finally.



After the removal I found that different size of nuts were used.  2 pieces of 12mm nuts and 2 pieces of 13mm nuts were used in the WEBER for #1 and #2 cylinders.  And all 12mm nuts were used for the other WEBER.  Moreover, some nuts had washers, some had spring washers, some had nothing…it was very random.  I supposed that the previous owner or shop changed some nuts from 13mm to 12mm because of the work space when they removed the WEBER.  Why didn’t they change all nuts to 12mm!  But I was too insensitive because I drove more than 10 years without knowing it!


The type of the WEBER was 40 DCOE 32.
Wow, very dirty WEBER!  I had to clean.  But this day was up to here.  



I cleaned the engine room little bit, but it was still dirty too.

Comments

Popular posts from this blog

Tip to repair rubber parts

I disassembled the rear axle before.  There had been no progress on it because I started the repair of the fuel tank during my summer holiday. While painting the fuel tank , I repaired the torn rubber boot of the parking brake wire. I guessed it didn ’ t cost high because it was small rubber part.  But I wanted to try the repair method I read on the magazine article before. This was the condition before the repair.  The rubber was torn apart and separated almost. I used this self-adhesive type butyl tape.  I pasted lots of small pieces of the butyl tape on the back side of the rubber boot.  As time goes by , these tapes would melt and stick together.  After this I applied plenty of adhesive “ Super X Black ” on the rubber boot.  On the magazine of MOTO MAINTENANCE , I read the article that the motorcycle seat was repaired with this method.  So , I wanted to try it. After drying 1 day , it became like this....

Brake master cylinder overhaul #1

I started the overhaul of the brake master cylinder after the clutch slave cylinder. This day ’ s work was removal and disassembly of the brake master cylinder. My “ onboro ALFA ” is early type ( Mk. I ) 1750GTV RHD.  The brake master cylinder is made by BONARDI and it is installed on the frame under the floor together with the clutch master cylinder ( this is made by BENDITALIA ) . Regarding the removal , there was a little try and error. ( 1 ) Remove the pipes Then , I tried to separate the linkage rod connecting to the brake pedal.  However , the fixing nut was so hard that I changed the process. ( 2 ) Remove the bolts fixing the brake master cylinder on the frame. ( These bolts were also fixing the clutch master cylinder penetrating the frame. ) ( 3 ) & ( 4 ) Separate the linkage rod from the brake pedal , and remove the brake master cylinder together with the linkage rod. ( The linkage rod and the pedal were fixed by a split pin. ) ...

Fuel pump (The original blog was written on 15th Aug. 2007)

Although the gas was refilled , the gas didn ’ t come to the carburetors.  The electric fuel pump was working , but it still did blank beating.  I replaced the pump soon after I bought this car…but it was about 20 years ago!  So , I decided to replace the electric fuel pump to new one , and to change the location of the pump from the engine room to the trunk room ( because for the electric fuel pump to push the fuel is better than to pull the fuel ) . I bought the Mitsuba electric fuel pump , fuel hoses and a fuel filter by auction and installed them in the trunk room.   ( The wiring is tentative.  But I am ashamed because the trunk room is so dirty… ) However , even the new fuel pump was working well , the fuel didn ’ t come.  I guessed that the inlet of the fuel sender unit in the tank was sticking.  I remove the unit from the tank and found the rusty unit and its inlet was perfectly blocked by the rust ( I forgot to take the pictu...