Skip to main content

Installation of the fuel tank #1: Fuel hose replacement

The repair of the fuel tank had been interrupted after the rust removal.  I started the installation of the fuel tank on the body.
Prior to the installation, I replaced the degraded fuel hose under the trunk room with new one.  About 30 years passed from 1969 when this car was produced, and the hose became hard and cracked.




The old hose was replaced with new hose.


The grommet at the body hole for the fuel hose was also degraded and cracked.  My stock grommet was little bit too small.  Then, I made a cut in one part of one grommet and spread it, and combined it with another 1/3 grommet.


At a glance it looked like a bigger grommet perfectly fitting to the hole. ☺︎


Moreover, I covered the hose with the corrugated tube to prevent the deterioration.


It could be relieved for a while with this


(My original blog was written on 26th Oct. 2008)
Labels:

Comments

Post a Comment

Popular posts from this blog

Tip to repair rubber parts

I disassembled the rear axle before.  There had been no progress on it because I started the repair of the fuel tank during my summer holiday. While painting the fuel tank , I repaired the torn rubber boot of the parking brake wire. I guessed it didn ’ t cost high because it was small rubber part.  But I wanted to try the repair method I read on the magazine article before. This was the condition before the repair.  The rubber was torn apart and separated almost. I used this self-adhesive type butyl tape.  I pasted lots of small pieces of the butyl tape on the back side of the rubber boot.  As time goes by , these tapes would melt and stick together.  After this I applied plenty of adhesive “ Super X Black ” on the rubber boot.  On the magazine of MOTO MAINTENANCE , I read the article that the motorcycle seat was repaired with this method.  So , I wanted to try it. After drying 1 day , it became like this....
2 comments
Read more

Brake master cylinder overhaul #1

I started the overhaul of the brake master cylinder after the clutch slave cylinder. This day ’ s work was removal and disassembly of the brake master cylinder. My “ onboro ALFA ” is early type ( Mk. I ) 1750GTV RHD.  The brake master cylinder is made by BONARDI and it is installed on the frame under the floor together with the clutch master cylinder ( this is made by BENDITALIA ) . Regarding the removal , there was a little try and error. ( 1 ) Remove the pipes Then , I tried to separate the linkage rod connecting to the brake pedal.  However , the fixing nut was so hard that I changed the process. ( 2 ) Remove the bolts fixing the brake master cylinder on the frame. ( These bolts were also fixing the clutch master cylinder penetrating the frame. ) ( 3 ) & ( 4 ) Separate the linkage rod from the brake pedal , and remove the brake master cylinder together with the linkage rod. ( The linkage rod and the pedal were fixed by a split pin. ) ...
Post a Comment
Read more

Fuel pump (The original blog was written on 15th Aug. 2007)

Although the gas was refilled , the gas didn ’ t come to the carburetors.  The electric fuel pump was working , but it still did blank beating.  I replaced the pump soon after I bought this car…but it was about 20 years ago!  So , I decided to replace the electric fuel pump to new one , and to change the location of the pump from the engine room to the trunk room ( because for the electric fuel pump to push the fuel is better than to pull the fuel ) . I bought the Mitsuba electric fuel pump , fuel hoses and a fuel filter by auction and installed them in the trunk room.   ( The wiring is tentative.  But I am ashamed because the trunk room is so dirty… ) However , even the new fuel pump was working well , the fuel didn ’ t come.  I guessed that the inlet of the fuel sender unit in the tank was sticking.  I remove the unit from the tank and found the rusty unit and its inlet was perfectly blocked by the rust ( I forgot to take the pictu...
Post a Comment
Read more