Skip to main content

Rear axle assembly restarted

After finishing the restoration of the fuel tank and related parts, I restarted the assembly of the rear axle which had been interrupted since summer holiday.  The first work was the assembly of the parking-drum brake.  It took little time to set the spring on the brake shoe.

At first I tried the following method, “to make the ring with a tie wrap, then to pull the spring with it”, which was taught from my friend.


It worked well with the smaller spring.  But when I tried it with the bigger spring, the tie wrap was broken out.  Probably the tie wrap was too narrow.

After trying several methods, I used the vice grip.  Grab the spring with the vice grip, pulled it with a full power and succeeded to set the spring.



I also painted the splash shield for the disc brakes.


Next would be the assembly of the rear axle hub bearing that was I struggled to remove.
I hoped the assembly would be easier…


(My original blog was written on 2nd Nov. 2008)
Labels:

Comments

Post a Comment

Popular posts from this blog

Tip to repair rubber parts

I disassembled the rear axle before.  There had been no progress on it because I started the repair of the fuel tank during my summer holiday. While painting the fuel tank , I repaired the torn rubber boot of the parking brake wire. I guessed it didn ’ t cost high because it was small rubber part.  But I wanted to try the repair method I read on the magazine article before. This was the condition before the repair.  The rubber was torn apart and separated almost. I used this self-adhesive type butyl tape.  I pasted lots of small pieces of the butyl tape on the back side of the rubber boot.  As time goes by , these tapes would melt and stick together.  After this I applied plenty of adhesive “ Super X Black ” on the rubber boot.  On the magazine of MOTO MAINTENANCE , I read the article that the motorcycle seat was repaired with this method.  So , I wanted to try it. After drying 1 day , it became like this....
2 comments
Read more

Brake master cylinder overhaul #1

I started the overhaul of the brake master cylinder after the clutch slave cylinder. This day ’ s work was removal and disassembly of the brake master cylinder. My “ onboro ALFA ” is early type ( Mk. I ) 1750GTV RHD.  The brake master cylinder is made by BONARDI and it is installed on the frame under the floor together with the clutch master cylinder ( this is made by BENDITALIA ) . Regarding the removal , there was a little try and error. ( 1 ) Remove the pipes Then , I tried to separate the linkage rod connecting to the brake pedal.  However , the fixing nut was so hard that I changed the process. ( 2 ) Remove the bolts fixing the brake master cylinder on the frame. ( These bolts were also fixing the clutch master cylinder penetrating the frame. ) ( 3 ) & ( 4 ) Separate the linkage rod from the brake pedal , and remove the brake master cylinder together with the linkage rod. ( The linkage rod and the pedal were fixed by a split pin. ) ...
Post a Comment
Read more

Fuel pump (The original blog was written on 15th Aug. 2007)

Although the gas was refilled , the gas didn ’ t come to the carburetors.  The electric fuel pump was working , but it still did blank beating.  I replaced the pump soon after I bought this car…but it was about 20 years ago!  So , I decided to replace the electric fuel pump to new one , and to change the location of the pump from the engine room to the trunk room ( because for the electric fuel pump to push the fuel is better than to pull the fuel ) . I bought the Mitsuba electric fuel pump , fuel hoses and a fuel filter by auction and installed them in the trunk room.   ( The wiring is tentative.  But I am ashamed because the trunk room is so dirty… ) However , even the new fuel pump was working well , the fuel didn ’ t come.  I guessed that the inlet of the fuel sender unit in the tank was sticking.  I remove the unit from the tank and found the rusty unit and its inlet was perfectly blocked by the rust ( I forgot to take the pictu...
Post a Comment
Read more